Browse "ME-Theses_Master(석사논문)" by Title 

Showing results 3521 to 3540 of 3882

3521
컴퓨타에 의한 공기조화부하계산 = Heating-cooling load calculation by computerlink

김두천; Kim, Doo-Chun; et al, 한국과학기술원, 1975

3522
컴퓨터 비젼 및 패턴인식 기법을 이용한 공구상태 판정 시스템 개발 = Tool condition monitoring technique using computer vision and pattern recognitionlink

권오달; Kwon, Oh-Dal; 양민양; 오준호; et al, 한국과학기술원, 1992

3523
컴퓨터 비젼을 이용한 공구 마모의 측정과 공구 파손의 검출에 관한 연구 = A study on tool wear measurement and tool failure detection using computer visionlink

허경회; Heo, Kyung-Hoe; et al, 한국과학기술원, 1991

3524
컴퓨터 수치제어 선반을 이용한 공작물의 진원통도 오차 보상제어 = Compensatory control of workpiece cylindricity error in C.N.C. turning processlink

황언; Hwang, Eon; et al, 한국과학기술원, 1988

3525
컴퓨터 시뮤레이숀을 통한 현장에서의 최적 절삭조건의 결정 : 일점일회 선삭에의 적용 = On shop optimum determination of cutting conditions by a heuristic method based on computer simulation : an application to single-point one-pass turninglink

이석호; Lee, Suck-Ho; et al, 한국과학기술원, 1979

3526
컴플라이언스 주파수 특성을 이용한 공작기계의 동적성능평가 = Dynamic performance test of machine tools by compliance-frequency characteristicslink

강윤식; Kang, Youn-Sik; et al, 한국과학기술원, 1986

3527
케이블 메커니즘을 사용한 재활 로봇의 능동 컴플라이언스 제어 = Active compliance control for the rehabilitation robot with cable transmissionlink

강상훈; Kang, Sang-Hoon; et al, 한국과학기술원, 2002

3528
켈리브레이션에 기반한 방법과 비주얼 서보잉을 이용한 메니퓰레이션 시스템의 비교연구 = A comparative study of a calibration-based manipulation and a visual servoing-based maipulationlink

박찬석; Park, Chan-Seok; et al, 한국과학기술원, 1996

3529
코너 모듈의 스티어 바이 와이어 시스템 센서 고장 진단 = Sensor fault diagnosis of steer-by-wire system in corner modulelink

진현우; 최세범; et al, 한국과학기술원, 2023

3530
코발트 금속유기골격체 기반의 웨어러블 디바이스용 신축성 마찰전기 나노발전기 = Stretchable triboelectric nanogenerator based on cobalt metal-organic framework for wearable deviceslink

유현준; 오일권; et al, 한국과학기술원, 2023

3531
코안다 효과가 기대되는 이차원 분류에 관한 실험적 연구 = An experimental study on the dimensional scoanda jetlink

최병일; Choi, Byung-Il; et al, 한국과학기술원, 1992

3532
코크스오븐가스 기반 혼합연료의 가압 수증기 개질 반응에 관한 연구 = Study on pressurized steam reforming of cokes oven gas-based fuel mixtureslink

전형준; 배중면; et al, 한국과학기술원, 2020

3533
콘 모양의 바닥을 가지는 축대칭 회전용기내의 스핀 엎 = Spin-up of a fluid in an axisymmetric rotating container with cone-shaped bottomlink

권기현; Kwon, Ki-Hyun; et al, 한국과학기술원, 1994

3534
콘테이너 크레인의 최적 설계 = An optimal design of container cranelink

박경진; Park, Gyung-Jin; et al, 한국과학기술원, 1982

3535
쾌속 서비스 로봇을 위한 스마트 그리퍼의 설계 = Design of smart gripper for rapid service robotlink

정태진; Jung, Tae-Jin; et al, 한국과학기술원, 2012

3536
쾌속운동을 위한 인간형 로봇 팔의 경량화 설계 = The light weight design of a humanoid robot arm for rapid movementlink

박상신; Park, Sang-Sin; et al, 한국과학기술원, 2007

3537
쾌속조형을 이용한 다이 캐스팅 제품의 시작 공정 설계 및 제작 = Design and development of trial die casting process by using rapid prototypinglink

김기돈; Kim, Ki-Don; et al, 한국과학기술원, 1999

3538
크랙 성장을 고려한 J-저항 곡선의 결정 = Determination of crack growth corrected J-R curveslink

윤기봉; Yoon, Kee-Bong; et al, 한국과학기술원, 1983

3539
크랙을 가진 이방성 접착구조물의 해석 = Analysis of adhesively bonded anisotropic structure with a cracked platelink

정광영; Jeong, Kwang-Young; et al, 한국과학기술원, 1982

3540
크랭크-콘넥팅로드계의 연결부에서의 힘 규명과 민감도 해석 = Force prediction on the joint of crank-connecting rod system and its sensitivity analysislink

양승환; Yang, Seung-Hwan; et al, 한국과학기술원, 1996

rss_1.0 rss_2.0 atom_1.0