3861 | 생산 능력을 고려한 발견적 롯트량 결정 기법 = A heuristic lot sizing algorithm with capacity constraintslink 오수철; Oh, Soo-Cheol; et al, 한국과학기술원, 1981 |
3862 | 단면절삭에서의 피복 초경공구의 마모 특성에 관한 연구 = Study on the wear characteristics of coated WC insert tool in outfeed facing operationlink 박장식; Park, Jang-Sik; et al, 한국과학기술원, 1981 |
3863 | 재인발 가공에서의 한계 인발비 및 성형 하중 예측에 관한 연구 = A study on the prediction of limit-drawing ratio and forming load in redrawinglink 박장호; Park, Jang-Ho; et al, 한국과학기술원, 1981 |
3864 | 연료 소비량을 최소화 하기 위한 엔진의 suboptimal control = Suboptimal control of engine for minimizing fuel consumptionlink 박형호; Park, Hyung-Ho; et al, 한국과학기술원, 1981 |
3865 | DDS 방법을 이용한 실제 절삭 작업하의 절삭 다이나믹스 규명 = Identification of cutting dynamics under actual working conditions using DDS methodologylink 변승완; Byun, Seung-Wan; et al, 한국과학기술원, 1981 |
3866 | 발견적 일정 계획 기법을 이용한 수주 생산체제에서의 자원 제약하의 일정 계획 = Resource-constrained scheduling in the job shop using project scheduling heuristic algorithmlink 김수영; Kim, Soo-Young; et al, 한국과학기술원, 1981 |
3867 | 축 대칭 복합 압출에 관한 상계해 = An upper bound analysis of the axisymmetric combined extrusionlink 김용환; Kim, Yong-Hwan; et al, 한국과학기술원, 1981 |
3868 | 포리에틸렌 파이프에 대한 저속 균열 성장 실험 = Slow crack growth behavior of polyethylene pipe materialslink 박관흠; Park, Kwan-Hum; et al, 한국과학기술원, 1981 |
3869 | 밀링용 3차원 공구 동력계의 설계 및 제작 = Design and manufacturing of 3-dimensional dynamometer for millinglink 박성하; Park, Sung-Ha; et al, 한국과학기술원, 1981 |
3870 | 생산 공정 계획 및 설계 : 낫에 관한 연구 = Manufacturing process planning and design : case study of "KOREAN SICKLE"link 김선명; Kim, Seon-Myung; et al, 한국과학기술원, 1981 |
3871 | 카이젬 로보트의 위치 제어에 대한 공기압 온-오프 서보의 응용 = Application of pneumatic on-off servo to the position control of an industrial robotlink 김성동; Kim, Sung-Dong; et al, 한국과학기술원, 1981 |
3872 | (A) study of tool wear in electro discharge machining = 방전 가공시의 공구마모에 대한 연구link Park, Jong-Soo; 박종수; et al, 한국과학기술원, 1981 |
3873 | 레이디얼 피스톤 유압모타의 효율과 성능 특성 = Hydraulic radial piston motor efficiency and performance characteristiclink 김형의; Kim, Hyoung-Wei; et al, 한국과학기술원, 1980 |
3874 | Prediction of temperature distribution in the two-dimensional bodies with heat source and radiation exchange present at the surface = 表面에서 熱源과 輻射熱交換이 있는 二次元 物體의 溫度分布 決定link Hong, Dong-Pyo; 홍동표; et al, 한국과학기술원, 1980 |
3875 | 펌프 제어형 전동 유압식 조타기구의 성능 해석 = Performance analysis of a pump-controlled electro-hydraulic steering gearlink 홍예선; Hong, Yeh-Sun; et al, 한국과학기술원, 1980 |
3876 | Optimal active control of a circular plate vibration = 원형판 진동의 최적 Active cntrol 에 대한 연구link Hong, Suck-Woo; 홍석우; et al, 한국과학기술원, 1980 |
3877 | Material requirement planning(MRP) 의 실재응용 및 MRP 기법상의 롯트량 결정기법들의 비용관계의 상호비교 및 검토에 관한 연구 = A study on the practical application of material requirement planning(MRP) and the cost comparison among lot sizing techniques used in MRPlink 주영섭; Joo, Yeong-Seop; et al, 한국과학기술원, 1980 |
3878 | 이온 질화 처리된 냉간 가공용 공구강의 충격강도 및 마모특성 = Impact strength and wear properties of ion-nitrided cold working tool steellink 한성규; Han, Seong-Kyu; et al, 한국과학기술원, 1980 |
3879 | 3차원 형재의 후방 압출 해석 = Analysis of backward extrusion for three-dimensional shapeslink 한철호; Han, Chul-Ho; et al, 한국과학기술원, 1980 |
3880 | 원통형 이온질화 피처리물의 온도특성 = Temperature characteristics of a cylindrical workpiece in ion-nitriding processlink 임윤철; Rhim, Youn-Chul; et al, 한국과학기술원, 1980 |